Okx app download

List of the contents of this article:

• 1, How are car interior ornaments usually pasted?
• 2, How to stick car stickers and the specific steps?
• 3, The correct method of car film tutorial the whole process
• 4, How to stick the reflective film on the car?
• 5、What glue should be used to firmly paste the car decorative strip

How are car interior ornaments usually pasted?

Use magic transparent double-sided adhesive points to stick. Stick it on the car with an air suction cup. Use the anti-slip mat to place the ornaments directly on the anti-slip mat.

Double-sided adhesive fixing: This is the most common and common fixing method. It has a good effect on fixing ornaments on the central console. It is relatively simple to use double-sided adhesive to fix, but if it takes a long time, the double-sided adhesive will stick to the central console of the car and cause pollution to the central console.

The simple way is to cut the discarded mouse pad into the size of the base, stick the ornament to the smooth side of the mouse pad with double-sided glue, and put the other side directly on the car! The fixing method of car trim parts: 1. Rearview mirror pendant.

How to stick car stickers and the specific steps?

1. Measure the size of the window and cut the film according to the size. The size must be suitable. If you can't be sure, the size can be slightly larger, but never smaller. Clean the window glass. This step is very important, because if there is dirt on the glass, even a little, it will affect the effect of the film.

2. Steps for car film: tailor the car film according to the size of the car window; wipe and clean the front and rear window glass;Use a baking gun to shape the car film; after the baking film is completed, finely cut the car film.

3. The pasting method of car stickers is as follows: Before pasting the film, first ensure that the working environment meets the requirements of dryness and less dust. Otherwise, dust and debris entering during work will affect the effect of the film. It is recommended to wash the car before pasting the film.

4. Prepare the sticker, as shown in the figure below: straighten the transfer film, as shown in the figure below: tear off the base paper of the car sticker in reverse; wipe the position where you want to stick the car sticker; stick the sticker first after aligning; then push up with a towel and push it to the end.

5. Car film is applied to car glass to control sunlight and ensure safety. In addition to sunlight control, its basic safety performance includes clarity, anti-glare, ultraviolet insulation, heat insulation, anti-scrature, adhesive glass fragments, sufficient shelf life and privacy protection, ensuring safe driving performance, etc.Increase the beauty.

The correct method of car film The whole process of car film tutorial

Steps for car film: tailor the car film according to the size of the car window; wipe and clean the front and rear window glass; use a roast gun Fix the car film; finely cut the car film after the baking film is completed.

Step 1: Wash the car, clean the inside and outside of the car, and drive the car to a clean and dust-free place and wait for the film to be applied. Step 2: Measure the size of the car window and cut the film according to the size. The size must be appropriate. If you can't grasp it accurately, the size can be slightly larger, but not smaller. Step 3: Clean the window glass.

Car filming steps: car film shaping front windshield with a certain arcBefore the film is installed and pasted, it must be fixed first. Cover the cut car film on the outside of the glass, point it with a hot air gun at the curved part that requires shaping, and apply the car film to the glass with a scraper while heating.

Car film is applied to car glass to control sunlight and ensure safety. In addition to sunlight control, its basic safety performance includes clarity, anti-glare, ultraviolet insulation, heat insulation, anti-scrature, adhesive glass fragments, sufficient shelf life and privacy protection, ensuring safe driving performance, etc. Increase the beauty.

Test method 1 Test the thermal insulation effect In regular car beauty shops or 4S stores, infrared test lights are generally equipped, so you can ask the merchant for a corner car film to stick to the glass first, put the test light on one side, and put your hand on the other side to feel the thermal insulation effect of the film.

Use a special water-squeezing tool to exclude other blisters, and then apply the car film, adjust the position left, right, up and down, and then use the scraper and the baking gun to apply the film. When closing the edge, you can also wrap the edge with a scraper to wrap the edge under the low temperature of the baking gun, so as to further give full play to the stickiness of the glue and prevent the edge of the film. Soak and work again.

How to apply the reflective film of the car?

Car reflective film pasting method: First of all, the car body needs to be cleaned, and it is best to spray diluted detergent on the cleaned body. After the cleaning work is completed, it is necessary to determine the car reflective film in the position that needs to be arranged. Then scrape out the moisture in the paper with hard cards and other objects and blow it dry with a hot blowgun.

stick it to the screen along the torn film, and tear off the protective layer inside. A good computer screen film is adsorbed by electrostatics, so when pasting, put the film on the screen and it will be automatically pasted.

m How to paste the reflective film? Is it simple? The 3m reflective film is relatively simple to paste. It adopts high-efficiency sub-sensitive backing glue, which is strong and durable, and perfectly bonds the substrate. At the same time, the thickness of the glue layer is moderate, and the engraving is convenient and efficient.It will not fall off at a high temperature of 60 degrees or a low temperature of minus 40 degrees.

It is possible that the protective film on the reflective film has not been torn off. Take a closer look. If it is not torn off, just tear it off.

First, tear off the acrylic reflective film from the backing paper or backing film. Secondly, stick it on the board quickly. Finally, smooth the acrylic layer repeatedly, and be careful not to tear it repeatedly. In this way, the acrylic reflective film is attached to the board.

What glue is used to paste the car decorative strip firmly

The decorative strip of the car is generally pasted with double-sided adhesive. The recommendation of double-sided adhesive is relatively well-known, 3m double-sided adhesive.

Car decoration strip. This can be pasted with double-sided adhesive.The choice of double-sided adhesive, this one with better quality and strong adhesiveness is fine. First, when pasting, you must pay attention to the cleanliness of the bonding surface, and there should be no oil stains and dust.

Clean the adhesive part of the decorative strip and the surface of the car body with cotton cloth dipped in alcohol (very important); dry the moisture on the car body and decorative strip with a roasting gun; glue the decorative strip with 3M double-sided adhesive, and bake it with a baking gun to maximize the viscosity of the double-sided adhesive; smooth the decorative strip, and press it with force and press it to stick firmly and firmly. Decorative strip.

The car decorative strip should be pasted with double-sided adhesive of the 3M brand. When pasting, pay attention to the cleanliness of the combined surface and there should be no oil stains. When pasting, the temperature should be appropriately higher, which is conducive to the perfect fit of the adhesive surface and the outer surface of the car.

The installation diagram of the car beauty decorative strip is as follows: First, use car cleaner or alcohol to clean the position that is about to be pasted.After clarifying the good_part, tear off the built-in 3M glue of the goods on both sides about 3 cm, but pay attention to the glue surface and the fingertips do not touch each other.